Baldor
Electric Motors
- General Purpose (TEFC and ODP)
- C-Face Capability (1 to 100 Hp)
- Chemical Processing (1 to 500 Hp)
- Washdown Duty (1 - 20 Hp)
- IEC Metric Frames (1.1 to 187 Kw)
- Totally Enclosed Fan Cooled - 1 to 800 Hp
- Chemical Processing - 1 to 500 Hp
- Explosion Proof - 1 to 350 Hp
- Open Drip Proof (ODP) - 1 to 2500 Hp
- Closed Coupled Pump - 1 to 60 Hp
- Single Phase - 1/4 to 5 Hp
- Chemical Processing (1-500 Hp)
- Super-E® Chemical Processing (1-400 Hp)
- IEEE 841 (1-500 Hp)
- C-Face (1-100 Hp)
- Dirty Duty™ (1/2-20 Hp)
- Crusher Duty (100-300 Hp)
- General Purpose Three Phase (1/8-800 Hp)
- Medium Voltage (100-2500 Hp)
- 200 Volt (1-100 Hp)
- 575 Volt (TEFC, ODP, Explosion-Proof)
- Single Phase (1/2-15 Hp)
- Metric IEC Frames (1/4-187 Kw)
- General Purpose Motors (1/2-20 Hp)
- "Paint Free" Motors (1/2-10 Hp)
- Baldor SmartMotor® (1-10 Hp)
- Washdown AC Drives (1-10 Hp)
- DC Motor and Controls (1/4-5 Hp)
- Rigid Base (1/4-350 Hp)
- Super-E® Premium Efficient (1-350 Hp)
- 1.15 Service Factor (3-300 Hp)
- C-Face/Pump (1/3-100 Hp)
- Inverter Drive® (1/2-200 Hp)
- Brakemotors (3/4-5 Hp)
- DC Motors (1/4-3 Hp)
- NEMA C-Face (1/4-100 Hp)
- Jet Pump (1/3-3 Hp)
- Closed Coupled (1-60 Hp)
- Pressure Washer (1 1/2-5 Hp)
- Vertical P-Base (3-75 Hp)
- Metric Mount (180W-30kW)
- Brake Motors (TEFC, ODP, and XPF)
- Two Speed Motors (1/4-100 HP)
- Automotive Approved (1-100 Hp)
- Design D, High Slip (3-250 Hp)
- Arbor Saw (7 1/2-15 Hp)
- Door & Gate Operator (1/3-3/4 Hp)
- General Purpose (1/3-10 Hp)
- Crop Dryer Motors (Up to 15 Hp)
- Irrigation Motors
- Definite Purpose (Grain Stirring Motor)
- Auger Gearmotor (1/4-1 1/2 Hp)
- Repulsion-Induction Motors (2-15 Hp)
- Multipurpose Control (2-800 Hp)
- Multipurpose Combination Starter
- Single Phase Starter (1/4-3 Hp)
- Definite Purpose Control (2-100 Hp)
- Three Phase Torque Control (1 1/2-30 Hp)
- Electronic Brakes (5-600 Hp)
- Fan and Blower (1/4-3 Hp)
- Condensor Fan (3/4-1 1/2 Hp)
- Direct Drive Fan Motors (1/4-3/4 Hp)
- Centrifugal Fan (5-30 Hp)
- Air Over Motors (1/4-10 Hp)
- HVAC Blower Motors (1/2-5 Hp)
- Right Angle (1/50-1/4 Hp)
- Parallel Shaft (1/50-1/2 Hp)
- Double Reduction (Up to 1200:1 Reduction)
- Flange Mount (Up to 1/4 Hp)
- Permanent Magnet DC Motors (1/50-1/4 Hp)
- Subfractional AC Motors (1/12-1/4 Hp TENV)
- Linear Induction Motors (Forces to 500 lbs)
- Brushless Servo Motors (Accelerations to 10g)
- Dual-Axis Steppers (Forces to 30 lbs)
- Enclosed Positioning Stage (Forces to 480 lbs)
- Single Bearing Positioning Stage
- DC Brush Type Servos (Accelerations to 5 g's)
